LCP-BK-K - Lightning Cable Protection Heatshrink Kit - Black

Lightning Cable Protection & Repair Kit

Are you tired of having to replace your lost or damaged Apple cords and chargers? Wirecare is here to help you. We have a variety of different techniques and products that could help you protect those valued cords!

Do your charging cords always rip where the cord enters the connector end? I’m sure you’ve seen a variety of expensive products that can prevent that from happening. However, Wirecare has a simple, easy and inexpensive method that is just as effective. We offer Heatshrink Tubing in a variety of colors and sizes that can add extra support and stability to those brittle cable ends. Heatshrink Tubing can be installed by following a few easy steps. This kit is compatible with the Lightning Cable Only

The Lightning cord is used with the following Apple products: iPhone 5S and Later, Ipod Tocuh 5th Gen and Later, Ipad Mini, Ipad 4th Gen and Later, and Ipad Pro.

Kit Contents:

• 1 ft - 3/8" 3:1 Polyolefin Heatshrink Tubing (In selected color)
• 1 ft - 1/2" 3:1 Polyolefin Heatshrink Tubing (In selected color)
• 6 in. - Hot Fusion Adhesive Tape
• Instruction Booklet

Step by Step Installation Instructions

STEP 1: Determine the correct size of Heatshrink based on your cable end. Choose the heatshrink size that fits snug but still allows the cable end to travel through.

STEP 2: Measure the length of Heat Shrink you need, making sure that it covers the damaged section (if applicable). Although you do not need to cover any part of the cable end, it is recommended to help keep the Heat Shrink from slipping.

STEP 3: Mark where to cut the Heat Shrink, and cut along designated line.

STEP 4: Using the Heat Shrink for reference, cut a strip of adhesive that will slide into the Heat Shrink along side the cable. Adhesive is Optional but recommended

STEP 5: It is ok if the adhesive seperates from it’s backing, the tape will not be sticky to the touch. It will become sticky once heated.

STEP 6: If our cable is damaged, remove any excess rubber or coating prior to applying Heat Shrink.

STEP 7: Slide the cut piece of Heat Shrink over the cable end. Depending on the size of the cable, it may be a very tight fit. If it does not fit your Heat Shrink may require some stretching. To do so, insert two dowels into the Heat Shrink and force them apart gently, continue to do so until the Heat Shrink fits over the cable end. Warning: If Heatshrink rips while stretching it will not work properly.

STEP 8: Check if your cable end has lights or anything else you shouldn’t cover while positioning the Heat Shrink. If applying adhesive, remove the backing and insert the strip along side the cable.

STEP 9: Once the Heat Shrink and Adhesive Strip are positioned properly, use a Heat Gun or other source of heat to heat the Heat Shrink slowly and evenly. This may take a few minutes, please be patient. Hold farther down the cable to prevent burning yourself.

STEP 10: Your cable is now protected or repaired!

WireCare® Heat Shrink Tubing Kit Varieties:

2:1 General Purpose Shrink Kits: These kits include 110 Precut pieces of our popular 2:1 Shrinkflex® heat shrink tubing. Six different diameter options come presorted in each container! This kit is available in all standard 2:1 Color options, as well as some kits featuring multiple colors.

3:1 General Purpose Shrink Kits: Similar to the 2:1 kits, These heat shrink kits include 110 Precut pieces of 3:1 Shrinkflex® tubing. Six different diameter options come presorted in each container and these are available in all standard 3:1 Color options, as well as some mixed varieties.

Adhesive Lined Shrink Kits: These kits include 110 Precut pieces of 3:1 Shrinkflex® Adhesive shrinktubing (also known as glue lined shrink). Six different diameter options come presorted in each container and these are available in a variety of colors.

WireCare® Master Kit: Can't decide which color pre-made heat shrink kit you want? The heat shrink master kit includes them all! This complete kit includes 1,100 pieces of 6" precut heat shrinkable tubing sorted by size and color into 10 drawers. This kit is great for keeping a wide range of diameters and colors on hand for your projects.

USB Cable Protection Kits: These kits are conveniently pre-cut Heat Shrinkable tubing intended to reinforce the USB cable where the wires meet the connector to prevent damage from bending & strain on the wire. No need to measure, or really think at all, since this kit comes with exactly what you need to repair or protect your USB cables.

Lightning Cable Protection Kits isten up apple lovers, we've got pre-cut Heat Shrinkable tubing to reinforce those delicate Apple lightning cable where the wires meet the connector so you never have to buy a new phone charger again. The kit includes everything you need to make your repair!

Magsafe 1 & 2 Cable Protection Kits: This Pre-Cut Heat Shrinkable tubing is cut specifically to reinforce those expensive Apple MacBook charging cables. No Need to measure, we've done all the legwork for you!

Use up some of the sizes in your kit? Each kit includes a full list of included materials specifying size, length and part numbers which makes reordering your go to sizes a breeze.

Uses for Heat Shrink Tubing

Heat shrink tubing (also referred to as shrink tube, heat tube, or shrinkable tube) has a wide variety of different applications in a multitude of different industries. Here are some of the most uses for heat shrink tubing:

• Color Coding wires for easy identification.
• Providing Strain relief on wire ends & connections.
• Repairing cables from strain related damage or wear-and-tear.
• Re-enforcing cable chargers & headphones
• Acting a protective covering to prevent scrapes, dents, or damage.
• Providing a clean termination for braided sleeving applications.
• Thermal Insulation for wires.
• Bundling of loose wires & cables
• Providing a weather tight seal on wire bundles.
• Adding extra grip to tool handles.
• Stopping chains from rattling.
• Temporarily stop small leaks in pipes & hoses until a permanent repair can be made.
• Preventing rope ends from fraying.

Different Heat Shrink Tubing Materials

Heat shrink tubing is currently manufactured in a wide range of thermoplastics geared towards specific applications. Here are some of the most common varieties of shrink tubing.

Polyolefin: This is the most commonly used heat shrink material and works for most heat shrink applications. Polyolefin comes in a variety of colors, sizes, shrink ratios, and has an operating temperature of -67° F to +275° F. Keep in mind, Polyolefin has a low tolerance for UV resistance compared to other shrink tubing.

PVC: Polyvinylchloride, or PVC heat shrink, is an economical solution ideal for lower temperature applications like food & beverage use. It also has a higher UV resistance than standard Polyolefin.

Fabric: Fabric heat shrink tubing is constructed using a combination of polyolefin and polyester. Fabric shrink is ideal for use in environments were retaining strength & abrasion resistance is important. This material often has a narrower operating temperature range as well as more longitudinal shrink than other shrink tubing materials.

PTFE: Polytetrafluoroethylene, or PTFE, is intended for use in applications where it is frequently exposed to very high temperatures. This material has a very high shrink temperature, making it difficult to shrink for most users without specialized heating equipment.

Kynar: Kynar heat shrink is highly flame retardant, abrasion resistant, and geared towards environments that require strain relief such as soldered connections and splices.

Viton: This shrink tubing is a fluid resistant, flame retardant flouro-elastomer with high solvent resistance intended for use in applications exposed to corrosive materials or high temp environments.

Thing To Consider When Choosing The Right Heat Shrink For Your Project

Shrink Ratio: The shrink ratio is the approximate maximum amount that heatshrink tubing will shrink relative to the unshrunk diameter. For example, 2:1 heatshrink shrinks to half of its original diameter ( 1” shrinks to ½”). If your wiring harness has large connectors or plugs that you would like to shrink over this must be taken into consideration when determining shrink ratio. Larger obstacles will need a higher shrink ratio in order to allow the tube to slide over while still allowing it to shrink into a tight fit for your cables.

Material: As discussed above, heat shrink tubing is available in a variety of different materials geared to specific applications, locations, and temperature ranges. Knowing the circumstances for your specific project allows you to determine if any of the customized protections provided by different materials are beneficial to you.

Shrink Temperature: The minimum amount of heat required for shrink tubing to begin the shrinking process is referred to as the material’s Shrink Temp. This temperature can vary due to material, wall thickness, or other factors. While choosing your heatshrink be sure to reference the shrink temp listed to ensure you have the tools required to reach the specified temperature. Heat shrink tubing with lower shrink temps can often be applied using a hair dryer, while materials with a higher temp require an industrial strength heat gun.

Environment: Where will your completed heat shrink project be located? Will it be exposed to weather, abrasion, UV, or chemicals? The final location of your wire harness will help you narrow down the amount of protection your heat shrink needs to provide. Harsh outdoor environments would likely need a fabric shrink, while applications that come into frequent contact with automotive fluids can be protected with Diesel Resistant Shrink. Be sure to read the protective qualities of your chosen heat shrink to ensure it aligns with your project's requirements.

Color & Aesthetics: Is the primary goal of your heat shrinking project aesthetic appeal over protection? Standard 2:1 or 3:1 Polyolefin heat shrink is available in the largest selection of colors and is the go to choice for those interested in using shrink tubing to color code or identify wiring. We even offer a yellow/green ground ID shrink tubing for easy identification of ground lines. If you are interested in taking your labeling to the next level, consider trying out our Heat Shrink Printing service where we can print your text, logos, and designs directly onto the tubing for you!